← Model histories

KrAZ-250

In 1980 the Kremenchuk vehicle plant produced the first industrial batch of KrAZ-250 chassis, introducing a new family. Specialist factories fitted lifting equipment, concrete mixers and pumps, cranes and other machinery for oil and gas extraction and construction.

Like the KrAZ-257B1A, the chassis was designed for roads permitting an 18-tonne tandem-axle load and temperatures from +40 to −40 °C. It could tow a trailer of up to 20 tonnes when required. The design maximised commonality within the new family and retained the most advanced, reliable components of earlier models.

Compared with the KrAZ-257B1A, payload rose from 13200 to 14575 kg and top speed from 68 to 75 km/h, while test consumption fell by 3 L/100 km. Maintenance took less time and labour: the TO-1 interval increased by 1000 km and TO-2 by 1500 km. Labour per 1000 km fell from 2.58 to 1.87 person-hours. Life before the first overhaul was 200000 km in the first operating-condition category. More efficient packaging shortened the bonnet and reduced the road area hidden from the driver.

КрАЗ-250

The new KrAZ differed not only in its completely new cab, front panels and bonnet: it also gained numerous new or improved components and systems, and greater comfort.

The three-seat metal cab gave the truck a distinctive exterior and interior. Seating and layout followed contemporary ergonomics, with an adjustable driver’s seat and a two-person passenger seat. Ventilation, heating, warm-air demisting including side windows, washers and wipers, two mirrors and a fan provided comfort. Storage, sun visors, radio, ashtray, document box and driver’s belt mountings were included. Doors had key locks, swivelling quarter-lights and winding windows. Cab and front panels formed a separate assembly attached to the chassis at four points.

Engine-system changes included a longer-lasting tube-and-strip radiator replacing the tube-and-plate type. The single-wire 24 V electrical system remained, but exterior lighting now met UNECE requirements. Warning lamps indicated high beam, indicators, low air-reservoir pressure, minimum engine oil pressure and coolant overheating.

Most changes concerned the chassis. A hydropneumatic clutch-release system with air assistance cut pedal effort fourfold. In the two-speed transfer case, the high ratio changed from 1.23 to 1.00, raising maximum speed. The front axle was shared with the MAZ-500A. Disc-less wheels similar to MAZ’s used radial tyres, and the rear suspension’s equaliser mounting was revised.

The service brakes became more effective and reliable, acting on every wheel. The split pneumatic system’s first circuit served front and intermediate axles, the second the rear axle. Trailer brakes used either a single- or dual-line connection according to their design. Front lining area increased. Either service circuit could provide reserve braking. A drum parking brake was fitted to the transfer case’s right output shaft.

Specifications KrAZ-250: Kerb weight - 9200 kg, Payload - 14575 kg. Wheel configuration - 6×4. Top speed - 75.km/h. Fuel capacity - 330 L. Dimensions: Length - 9520 mm. Width - 2500 mm. Height - 2695 mm. Loading height - 1080 mm. Wheelbase - 4880 mm from front axle up to intermediate axle and 1400 mm rear bogie. Track - 1870 mm front and 1833 mm rear. Ground clearance - 275 mm. Engine: model - YaMZ-238. Cylinders - 8. Displacement - 14860 cm³. Power - 240 hp at 2100 rpm. Transmission: Clutch - dry twin-plate. Gearbox - manual, three-rail five-speed. Transfer case - manual, two-speed with lockable centre differential. Final drive - double-reduction with spiral-bevel and spur gears. Ratio - 8,21. Running gear: front suspension - rigid axle with longitudinal leaf springs and telescopic dampers, rear - equalising with longitudinal leaf springs. Tyres - 300—508R.

Source: журнал «За рулем»